展示全部
差的色变化为色球差,称上图所示的曲线为色球差曲线。从色球差曲线还可以看出,虽然对F光和C光在0.707带校正了色差,但其公共焦点相对于主色光D线尚有较大的偏离,约为0.053。这种二色光的公共焦点相对于主色光的位置差异称为二级光谱。如果要求光学系统具有极好的像质,除了必须很好地校正球差和位置色差外, 还需对色球差和二级光谱进行校正,但这是非常困难的,只有当系统有相当复杂的结构才有可能。同时校正位置色差和二级光谱即是对三种色光消色差,这种系统称为复消色差系统。相关文献:《几何光学 像差 光学设计》(第三版)——李晓彤 岑兆丰您可以通过我们昊量光电的官方网站www.auniontech.com了解 ...
图所示的三 色球差曲线。据此可全面判断轴上点像差的校正状况。垂轴平面上近轴轴外点或大孔径小视场系统的轴外点,只要根据轴上点光线的追迹结果,就能通过计算正弦差值来判知其 像质。远离光轴的点会产生所有像差,因此需对轴外点进行全部像差的计算。这种计算至少应对边缘视场和 0.707视场点进行,每点的孔径取值与轴上点相同。对于绝大多数能以二级像差表征高级像差的光学系统,以上计算已足够。对于那些不能忽略高级像差的系统,计算的光线数应该有所增加。 一般计算六个视场点,取值为 Kw = -1,-0.85,-0.707,-0.5,-0.3和0。上世纪80 年代以前计算机软、硬件条件还比较差,设计条件十分有限,编 ...
正二级光谱和色球差就相当不易。后者常只能以不同程度地减小相对孔径才能实现。这类物镜常用的型式有:1.双胶合物镜在玻璃选择得当时,能同时校正色差、球差和彗差,是可能满足像质要求的zui简单形式,但胶合面上的高ji球差使相对孔径受到限制,且当用普通玻璃时,二级光谱为常量,色球差也无法控制,因而不能获得高的像质。该型式的优点是结构简单,工艺方便,光能损失也小,宜于在焦距不长、相对孔径不大的场合采用。2.双分离物镜当口径大于50~60毫米时宜采用双分离物镜。这种物镜在玻璃选得恰当时,除能校正好色差、球差和彗差外,还能利用灵敏的空气问隙的少量变化来校正带球差,因此可达到相当大的相对孔径,但色球差和二级光 ...
对二级光谱和色球差作严格的校正而成,因此在小视场范围内有极高的成像质量。为校正二级光谱,部分透镜需要采用特殊色散的光学材料,如萤石(CaF2)或特种光学玻璃。这些材料的折射率均很低,又要校正色球差,故复消色差物镜的结构要较消色差物镜复杂得多。下图5为一数值孔径为1.25 的100倍复消色差物镜,其中阴影部分是萤石透镜。由于这种物镜倍率色差较大,需与相应的补偿目镜配合使用。图5三、平场消色差物镜和平场复消色差物镜由于复消色差物镜仍然具有较大的像面弯曲,不能在平的接收面上给出整个视场的清晰像,为作显微投影或显微摄影,zui好应用平场物镜。这种物镜的主要问题是设法减小或校正匹兹凡和,办法是在系统中加 ...
或 投递简历至: hr@auniontech.com