以采用通用的单模光纤或多模光纤就能满足要求。有时,为了提高传感器的灵敏度,而增大光纤传输的光功率,可采用大芯径或大数值孔径光纤,甚至采用光纤传光束或者塑料光纤,以提高与光源的耦合效率。在相位调制型光纤传感器中,为了获得测试光信号与参考光信号间高的相干度,而采用保偏光纤,使测试光纤与参考光纤输出光信号的振动方向一致。而在偏振调制型光纤传感器中,要求光信号的偏振态能敏感外界被测量的变化,则必须使光纤的线双折射尽量低,如低双折射液芯光纤。在分布式光纤传感器中,为了测量不同点的参量,可采用掺杂(如某些稀土元素或过渡金属离子)光纤或光栅光纤等。图2.光纤传感器的内信号的变化情况结语:根据光纤传感的工作原 ...
行)光耦合至单模光纤内。光纤准直器通过透镜能实现将从发散角较大(束腰小)的光束转换为发散角较小(束腰大)的光束,从而以较低损耗耦合进入其他光学器件。一、光纤准直器原理光纤端面输出的光近似为束腰半径较小,发散角较大的高斯光束。在两个准直器进行耦合时,光束束腰在中间位置,耦合损耗最小,这就是准直器所需要的工作距离。所以实际准直过程是将尾纤端面放在准直透镜的焦距位置,然后微调尾纤与透镜的距离,将准直后光束的束腰放在工作距离,以保证耦合效率。二、分类光纤准直器主要有两种:自聚焦透镜G-LENS(Grin Lens),其特点是折射率分布径向减小,能够使其中传输的光线产生连续折射,从而实现汇聚。球面透镜C ...
9 um的单模光纤,将有约17 dB 损耗,即损失约98%的光功率。2.光纤几何特性与波导差异导致的连接损耗。比较重要的特性差异因素有两类,即纤芯直径差异与数值孔径差异。(1)纤芯直径差异对连接损耗的影响。若两段光纤纤芯直径不同,在光纤轴线精确对准的条件,则连接损耗可以近似地由发射与接受纤芯面积的相对差值决定。图1.光纤纤芯直径差异例如,对渐变折射率光纤,50 um标准光纤芯径的允许变化值为±3 um。对于最大偏差情况,光从芯径为53 um的光纤中传输到47um的光纤中,其相差值为0.21。若光在纤芯中是均匀分布的,则计算损耗约为1 dB;类似地对单模光纤,其模场直径为8.4±0.5um,在 ...
的。例如,对单模光纤只激发出基模;对多模光纤光纤则激发出多种模式,它们各有不同的传输速度,即群速度不同。因而在到达光纤终端时,各种成分(如不同波长、不同模式)间产生时间差,速度快的先到,速度慢的后到,结果导致脉冲展宽,引起复杂的光纤色散现象。可以认为群时延是以时间单位度量的实际脉冲宽度。结语:为了保证通信质量,对色散造成的脉冲展宽必须加以限制,即对光纤能传输的最高数码率加以限制。光信号通过光纤传输引起信号畸变、脉冲展宽。由于光信号能量是由不同频率和模式成分共同承载的,因而引起色散的原因与机理也是多方面的。您可以通过我们的官方网站了解更多的产品信息,或直接来电咨询4006-888-532。 ...
导色散;以及单模光纤中不同偏振模式传输速度不同而引起的偏振色散。一、模间色散多模光纤中,即使对同一波长,不同传输模式仍具有不同的群速度,即长波速度不同,由此引起的脉冲展宽称为“模式色散”。在多模光纤中,模式色散引起的脉冲展宽是各种色散因素中影响最严重的一种。并且,传输的模式越多,脉冲展宽也越严重;另外,在多模光纤中,渐变折射率多模光纤由于其自聚焦效应,色散性能得到一定程度的改善,因而其模式色散的脉冲展宽较阶跃折射率光纤的脉冲展宽可减小约两个数量级。图1.光纤色散示意图以多模阶跃折射率光纤为例,对模式色散进行时域分析。在全部传导模中,低阶模几乎与光轴平行传播,传输速度快,最先到达出射端;而高阶模 ...
何尺寸极小(单模光纤的芯径不足10 um),所以要求光源器件要具有与光纤较高的耦合效率。结语:能够满足以上要求的光源一般为半导体发光器,另外全光纤激光器作为一种新型的激光器也有望在光纤通信系统中发挥其作用。目前,光纤通信中最常用的半导体发光器件是LED和LD。前者可用于短距离、低容量或模拟系统,其成本低,可靠性高;后者使用于长距离、高速率的系统。您可以通过我们的官方网站了解更多的产品信息,或直接来电咨询4006-888-532。 ...
根端面镀膜的单模光纤组成,导管既实现了腔体的密封又保证了两个端面的同轴平行。相对于本征型光纤法珀传感器,非本征型由于其结构,有以下特点:a) 由于法珀腔是由导管封装而成,所以可以根据需求人为的设计和调整腔长d,这样既可以精确控制腔长又能灵活调整腔长。b) 法珀腔内是折射率为1的空气,介质稳定,且不易受干扰。c) 如果采用与光纤热膨胀系数相同的材料做导管,可以很好地解决传感器的温度效应,这是普通法珀传感器所实现不了的优势。三、测压原理将法珀腔中一个端面制作成薄片,并用此薄片感受压力,当压力作用于薄片时,薄片发生形变,进而改变了法珀腔的腔长,通过解调求出腔长的变化量,根据腔长变化量和压力作用相关原 ...
了1.3微米单模光纤通信系统,即第三代光纤通信系统。80年代中后期又实现了1.55微米单模光纤系统,即第四代光纤通信系统。用光波分复用提高速率,用光波放大增长传输距离的系统,为第五代光纤通信系统。图1.通信技术迭代二、光纤技术的发展特点(1)频带极宽,通信容量大。光纤比铜线或电缆有大得多的传输带宽,光纤通信系统的光源调制特性、调制方式和光纤色散特性。对于单波长光纤通信系统,由于终端设备的电子瓶颈效应而不能发挥光纤带宽大的优势。通常采用各种复杂技术来增加传输的容量,特别是现在的密集波分复用技术极大地增加了光纤的传输容量。(2)损耗低,中继距离长。目前,商用石英光纤损耗可低于0~20dB/Km,这 ...
光波分复用技术的光纤通信分析摘要:光波分复用(Wavelength Division Multiplexer,WDM)的概念是指在一根光纤中能同时传输多波长的光信号。其基本原理是在发射端复用器将不同波长的光信号组合起来(复用),并通过一根光纤传输,在接收端解复用器又将组合的光信号分离开(解复用)并送入不同的终端。因此,称此项技术为波长分割复用,简称光波分复用(WDM)技术。其中,复合器合并光信道,解复用分离光信道。光波分复用技术对充分挖掘光纤带宽潜力,网络扩容升级,发展带宽新业务,实现超高速通信等具有十分重要的意义。尤其是WDM加上EDFA对现代光通信技术的发展更是具有强大的推动力。波分复用技 ...
- α)。当单模光纤指向太阳时,捕获了光谱。3. 高分辨率中阶梯光栅光谱仪RS40K的应用下图展示了RS40k中阶梯光栅光谱仪的性能。每个光谱都是在一次拍摄中获得的,包含430-950 nm的数据。某些光谱被限制在其范围内,以更详细地显示特别有趣的特征。光源表征二极管激光器发射的光束通常具有很小的波长范围,称为激光线宽。这是由于在激光二极管的谐振腔内同时发生多种不同模式的振荡。这些可以包括纵向和横向模式,导致多模激光二极管。下图显示了一种廉价光纤故障检测器的光谱,其中心峰波长为650±20 nm。汞在紫外和可见光区域有几条显著的光谱线,包括546.07 nm、435.83 nm和579.07 ...
或 投递简历至: hr@auniontech.com