高效的微米级相位调制器简介:介绍了基于绝热微环谐振器的可见光谱氮化硅热光相位调制器,具有器件占用空间小和低功耗,可用于AR/VR眼镜、量子信息处理电路和光遗传学等应用.作者:Guozhen Liang,Heqing Huang...Nanfang Yu原文链接: https://www.nature.com/articles/s41566-021-00891-y7 论文标题:超快计时实现无需重建的正电子发射成像简介:证明了无需层析重建的正电子发射成像。切伦科夫辐射探测器检测由正电子-电子湮灭产生的伽马射线,以4.8mm的精度确定正电子源的位置。作者:Sun Il Kwon ,Ryosuke O ...
为对入射光的相位调制)、层与层之间的距离都是可训练的参数。训练数据集由55000张来自于MNIST数据集的图片和55000张作者自己建立的数据集组成,首先通过数值模拟同轴全息记录过程,将生成的全息图导入衍射网络,衍射网络的层与层像素之间的联系由衍射理论确定,得到重建图像。然后通过最小化目标图像与推测的重建图像之间的误差优化网络参数,从而完成网络训练。网络的训练过程中可以将衍射层的加工误差和重建距离等因素考虑进去,增强衍射网络的鲁棒性。实验结果:参考文献:Md Sadman Sakib Rahman and Aydogan Ozcan, "Computer-Free, All-Opti ...
益介质里的自相位调制,产生一个可支持稳定模式锁定的色散范围)指导如何构建一个稳定的锁模腔,在构建用于特定实际应用的振荡器的时候,还是需要用到反复试错法,特别是使用离散值GTI反射镜的时候。我们需要逐渐增加负色散,直到获得稳定的锁模激光输出。作者发现,每个GTI反射两次(一个腔内往返周期为8次反射)可以产生稳定的锁模腔,且装配简单。被动锁模可通过激光束被一个高反射率曲面镜M4(r=1000mm, Layertec)聚焦到作为末端反射镜的半导体可饱和吸收镜上(SESAM, SAM-1040-2-25.4g; Batop GmbH, Jena, Germany,半导体可饱和吸收镜的调制深度(或非线性 ...
造电光幅度和相位调制器,这两种晶体具有高电光系数和良好的光学和电学性能。这些晶体生长在大的、低散射损失的晶锭中,并具有宽的透明度窗口。它们也是非吸湿性的,因此它们可以在光学平台上无限期放置,而无需密封外壳。相位调制相位调制器是最简单的电光调制器。在这里,电场沿晶体的一个主轴施加。沿任何其他主轴偏振的光会经历折射率变化,因此光程长度会发生变化,这与施加的电场成正比。因此,从晶体中射出的光场的相位取决于所施加的电场。最常见的体相位调制器是横向调制器,如图 1 所示,它由平行电极之间的电光晶体组成。这些调制器在电极之间产生大电场,同时提供长的相互作用长度,在其中积累相移。通过在电极之间施加电压 V ...
现对入射光的相位调制。但由于液晶的一些特性,驱动电压改变量和相位改变量是非线性关系,实际使用中需要测量并确定相位调制特性曲线。现介绍一种相位分析方法——白光干涉法,来确定LCOS芯片的相位调制特性曲线。白光干涉法采用迈克尔孙干涉仪的结构,在参考镜前设置补偿玻璃板(同LCOS芯片前的玻璃板),消除对光路的影响,从而使参考光和反射光达成白光干涉条件。分析干涉图可得到LCOS芯片的相位轮廓,进而分析相位调制的特性曲线。上图为白光干涉法的装置示意图。白光由确定中心波长的卤钨灯发射,经毛玻璃散射。然后由线偏振片获得与LCOS液晶指向矢平行的偏振方向。然后分束镜将透射光分为两路,一路光反射到参考镜经过补偿 ...
它具有与横向相位调制器的四分之一波电压类似的形式。由于这些晶体双折射的温度依赖性,这种简单的几何形状对于大多数电光晶体来说是不实用的。这种依赖性将温度相关的波片引入调制器。因此,使用双折射非线性介质(例如 LiNbO3)的未补偿调制器的传输将表现出显着的热漂移。这种温度敏感性可以通过稳定单晶调制器的温度或使用两个相同的晶体来克服。第二种方案采用光学串联放置的两个等长晶体,它们的主轴相对于彼此旋转 90°,如图 3 所示。因此,光束的偏振分量在两个折射率区域中的每一个中传播相等的路径长度,这导致结构的双折射为零,与温度无关。热漂移限制了相位调制器的实用性,相位调制器通常由单晶制成。实际限制这些设 ...
物镜60×用相位调制激光束在样品平面上产生m × n激光聚焦阵列。6个微粒被3 × 2激光聚焦阵列捕获。捕获粒子的拉曼散射信号通过二向色镜从激光中分离出来,经过透镜和多缝阵列后,直接进入光谱仪。图2采用1340 × 100像素的多通道CCD 对所有捕获粒子的拉曼光谱进行检测。图2为CCD相机捕获的拉曼信号。通过调节两排激光聚焦阵列之间的间隔距离,可以很好地分离两排拉曼信号,没有串扰。然而,每一行有三个拉曼信号显示了重叠和叠加,这是不可避免的。为了分解每一行叠加的光谱并检索单个光谱,可使用调制多焦检测技术进行光谱采集和重建。图3调制多焦检测的第一种方法是激励多焦阵列的调制,如照明调制。一条线上使 ...
图1.SLM相位调制与DMD振幅调制示意图由于激光是相干的,激光束的理想空间横截面在相位上是恒定的。液晶屏可以对相位进行一定程度的调制如图1a,c,e所示。这是各种后续技术的基础,这些技术以某种方式利用激光的空间调制相位,如图2所示。一个例子是使用空间相位调制将全息图案压印到连续波激光波前上。将液晶显示器放置在透镜的后焦平面上将导致在前焦点处的激光上印记的空间变化的相位图案的傅里叶变换。通过适当选择相位全息图,入射激光可以被调制成聚焦到多个空间分离的点,允许计算机控制多个激光焦点,就像用于光学捕获一样多聚焦激光扫描显微镜。液晶空间光调制器(LC-SLMs)也通常用于塑造超快激光脉冲和光学系统的 ...
往具有不同的相位调制特性,且相位调制精度容易受到运输过程、使用环境等因素的影响,因此在使用前对其进行测试与标定,是将其应用于波前调制与波前校正中必不可少的环节。为提高液晶空间光调制器(LC-SLM)在波前相位调制中的精度,曾婧潇等人提出一种能对 LC- SLM 实现快速标定的数字全息测量方法。该方法仅需在成像面上采集单幅数字全息图像,就能实时测量 LC-SLM在特定波长下的相位调制特性,系统结构简单,且无需经过复杂的衍射传播计算,测量效率较高。数字全息技术是一种利用数字全息图记录样品干涉信息,从而重构计算出被测物波的波前相位与振幅的技术,具有单次曝光、实时测量的特性。可以利用这项技术快速获得经 ...
SLM应用于激光扫描显微系统中的优势激光扫描显微镜,如共聚焦或双光子荧光,通过使生物组织在生理条件下的高分辨率成像成为可能,已经彻底改变了生命科学。激光扫描通常是用一对振镜或声光调制器来完成的。在这些扫描模式中,通过以光栅方式逐点逐行移动激光束来重建图像。这种方法的缺点是时域分辨率受到扫描器有限响应时间的限制。即使有可能提高设备的扫描速度,也会出现一个更基本的限制。为了以更短的每像素停留时间(即光束停留在样品中某一点并从该点收集光信号的时间)来维持足够的荧光信号,通常需要增加激光强度。然而信号采集的速率受到存在的发色团分子的数量和它们被激发的频率的限制。因此即使在完全没有光损伤的情况下,激发强 ...
或 投递简历至: hr@auniontech.com