息意味着更大视场,更高的空间分辨率、时间分辨率,更多的空间维度,需要相位信息等。如RUSH(传送门1)、傅里叶叠层成像等都是基于此目的而设计。传统的光学成像是所拍即所需。而计算成像往往是所拍只是所需的输入,还需要经过复杂的后端计算处理才能获得符合人们需要的图像。计算相位成像能够从强度测量重建出复数值,即包含振幅和相位信息,能揭示包含在介质固有的光学属性中的信息(传送门2)。当计算相位成像与获取更多信息的理念相碰撞,则激发出各种各样用于解决大规模(即大数据量)相位重建问题的方法。本文的作者提出的大规模相位复原方法得到业界巨佬Gabriel Popescu(相关文章,见传送门3,4.其SLIM一文 ...
像系统在整个视场内的模糊是变化的,即有着空间变化的PSF(主要由随视场变化的像差引起)。这激发了空间变化解卷积方法的应用。但是目前的大多数空间变化解卷积算法计算量大、计算慢,不适于实时图像重建。而且,它们重建的图像质量也不佳,这种现像在具有大空间范围PSF的高度多路复用成像系统、选择不当的先验等情况下更明显。虽然已有基于深度学习的解卷积方法被证明可以提高图像质量和重建速度,但是迄今为止,这些深度学习方法依赖于平移不变PSF近似,且不能很好的推广到具有视场变化像差的光学系统。快速迭代收敛阈值算法:fast iterative shrinkage-thresholding algorithm(FI ...
镜的高分辨率视场 (FOV) 通常约为透镜直径的 1/5。更大的透镜直径可以以更多的组织损伤为代价获取更大的 FOV。然而,成像体积与插入体积的比率几乎没有变化。当前不足:微型光学探头的一个缺点是组织探测区域小,这限制了其实际应用时的吞吐量和成功率。例如,如果感兴趣的神经元不在探头的成像体积内,则需要额外的动物和手术。因此,迫切需要一种能够在更大的组织体积内实现高分辨率成像,从而提高成像通量、灵活性和成功率的技术。文章创新点:基于此,美国普渡大学的Bowen Wei(第一作者)和Meng Cui(通讯作者)等人提出了一种清晰光学匹配全景探测通道技术(Clear Optically Matche ...
, 这样不同视场角的主光线在焦平面上平行。与像方远心对应的是物方远心,两个系统的串联组合构成双远心。当扫描镜头被称为远心时,通常意味着镜头不仅满足 F-θ 条件,而且光阑被放置在扫描设备上,以确保远心性。为了构建双远心中继系统,第一个中继透镜放置在扫描镜之后一个焦距处,第二个中继透镜放置在物镜后背孔径之前一个焦距处,中继透镜之间的距离为二者的焦距之和。请注意,远心区域位于镜头之间,而其他双远心系统则在中继系统的任一侧都是远心的。由于中继透镜的位置,这种配置被称为 4f 中继系统。它们的焦距之间的任何差异都会导致一定的放大倍数。DOI:https://doi.org/10.1364/AOP.7. ...
具有一定大小视场光学系统,必须校正倍率色差。为计算倍率色差值,需要对要校正色差的二种色光计算主光线的光路,然后求出它们与高斯像面的交点高度 y'F和y'C,再按上述公式求得。物镜的倍率色差很小或几近为零。这是因为物镜的位置色差已经校正,倍率色差也 随之校正之故。另外,倍率色差显然与光阑位置有关,因光阑与物镜重合,倍率色差也不会产生。例如,单个薄透镜不可能校正位置色差,当光阑与之重合时倍率色差为零;而当光阑位置移动时,倍率色差就要随之变化。当光阑位于透镜之前时,如下图所示,因,F光比C光偏折角度更大,y'F<y'C,故产生负的倍率色差;反之,如光阑位于透镜之后,则 ...
透镜是一个大视场、小相对孔径的物镜,并且应是线性成像物镜。透镜后扫描就是扫描器位于透镜后面,由激光器发出的光束首先被聚焦透镜聚焦,然后经置于焦点前的扫描器使焦点像呈圆弧运动。这类聚焦透镜通常是小视场、小相对孔径的望远物镜,前者物镜设计困难,但其他问题的处理则很简单。后者物镜的设计是简单的,但由于像面是圆弧形的,处理就很困难。因此,要求高的扫描装置通常采用透镜前扫描。线性成像物镜介绍什么是线性扫描成像物镜?首先,由于扫描元件的运动被以时间为顺序的电信号控制、为了使记录的信息与原信息一致,像面上的光点应与时间成一一对应的关系,即理想像高与扫描角成线性关系,有但是,一般的光学系统,其理想像高为使以等 ...
下F数为)大视场的远心光学系统,要求具有一定的负畸变,在整个视场上有均匀的光强度和分辨率,不允许轴外渐晕存在,并要达到衍极限性能。玻璃材料的质量与透镜表面的均匀性要求比一般透镜更为严格。相关文献:《几何光学 像差 光学设计》(第三版)——李晓彤 岑兆丰更多详情请联系昊量光电/欢迎直接联系昊量光电关于昊量光电:上海昊量光电设备有限公司是光电产品专业代理商,产品包括各类激光器、光电调制器、光学测量设备、光学元件等,涉及应用涵盖了材料加工、光通讯、生物医疗、科学研究、国防、量子光学、生物显微、物联传感、激光制造等;可为客户提供完整的设备安装,培训,硬件开发,软件开发,系统集成等服务。您可以通过我们昊 ...
中孔径光阑和视场光阑是任何光学系统都具有的两种主要光阑。有些系统中还有渐晕光阑和消杂光光阑。孔径光阑、入射光瞳和出射光瞳限制轴上成像光束立体角的光阑,称为孔径光阑(简称,孔阑)或有效光阑。孔径光阑经由前面的光组在物空间形成的像称为入射光瞳,简称入瞳。完全决定进入系统参与成像的最大光束孔径,是物面上各点发出进入系统成像光束的公共入口。孔径光阑经由后面的光组在像空间形成的像称为出射光瞳,简称出瞳。是物面上各点发出的成像光束经过光学系统后的公共出口。合理的选择系统孔径光阑的位置可以改善轴外点的成像质量。同时,当光阑的位置改变时,光阑的口径也要随之变化,以保证轴上点光速的孔径角度不变。孔径光阑的口径的 ...
,通过光斑在视场内的nm级位移来实现样品的成像。这种方式可以方便的和磁场,低温,CVD等其他设备结合在一起,实现“绝对”的原位测试,避免位移平台本身重复精度累积带来的成像扭曲和定位偏差。而全新推出的光子反聚束测量模块,在原本拉曼光谱、荧光寿命、光电流成像的基础上新增光子反聚束功能,在方便快捷的进行零声子线的测试的同时,还可以完成光子反聚束的测量,极大的简化色心的搜寻流程,迅速判断制备工艺水平。该模块有助于研究者用拉曼光谱和光致发光(PL)成像来表征样品,快速确定目标区域(可能有单光子源的区域),随后在同一仪器来进行反聚束实验。典型案例:对已经进行过氮离子注入处理过的纳米级金刚颗粒进行光谱分析, ...
阴极对不同的视场接受的光照比较均匀,所以成像物镜应尽量设计成像方远心光学系统。对于目镜来说,荧光屏可以看成是自身发光的图像,孔径光阑只要与眼瞳匹配即可。被动式红外系统本身不带有红外光源,而是直接探测目标发出的红外辐射。凡是绝对零度以上的物体都会发出红外线,但由于不同的物体之间、物体的不同部位、以及物体与环境之间温度不同,发射的红外线的波长和强度也就各不相同。温度较低的物体发出的红外线主要分布于远红外区,而温度较高的热源如发动机等发出的红外辐射波长在中红外区,辐射强度也相当高。利用这些辐射特性的差别,并通过对红外光进行光电、电光转换,可以得到人眼可视的图像。因此,这种图像反映的是目标的辐射温度分 ...
或 投递简历至: hr@auniontech.com