,通过从相机视场中稀疏分布的发射点来估计单个分子的位置,从而克服了分辨率的衍射限制。可实现的分辨率受到定位精度和荧光标签密度的限制,在实践中可能是几十纳米的数量级。有科研团队已经将这种技术扩展到三维定位。通过在光路中加入一个圆柱形透镜或使用双平面或多焦点成像,可以估算出分子的轴向位置。光斑的拉长(散光)或光斑大小的差异(双平面成像)对轴向位置进行编码。将空间光调制器(SLM)与4F中继系统结合到成像光路中,可以设计更广泛的点扩散函数(PSF),为优化显微镜的定位性能提供了可能。利用空间光调制器(SLM)对荧光显微镜进行校准,可以建立一个远低于衍射极限的波前误差,SIEMONS团队就利用Mead ...
密度。对于大视场系统,测量的空间均匀性是由栅边位置分布或倾斜决定的。在大尺寸传感器中,门信号的倾斜和高频信号切换期间可能的电压下降导致阵列的门边缘非均匀性。随着栅极长度的增加,上升边缘倾斜明显缩小(在表1的最后一行旁边)。这种效应可以归因于信号转换期间电源电压波动水平的差异。第一门信号跃迁(对应于大门的下降沿窗口自门推进对激光触发)导致门信号下降空间电源电压不平衡树,结果在第二斜门信号转变,在这种情况下,上升的边缘。随着栅极长度的增加,在较长的过渡延迟期间,电压降的较好的恢复降低了歪斜。由于栅门不均匀性的来源是确定的,它可以通过测量后的校准校正,如下一节所述。闸门性能的另外两个关键参数是上升和 ...
点或大孔径小视场系统的轴外点,只要根据轴上点光线的追迹结果,就能通过计算正弦差值来判知其 像质。远离光轴的点会产生所有像差,因此需对轴外点进行全部像差的计算。这种计算至少应对边缘视场和 0.707视场点进行,每点的孔径取值与轴上点相同。对于绝大多数能以二级像差表征高级像差的光学系统,以上计算已足够。对于那些不能忽略高级像差的系统,计算的光线数应该有所增加。 一般计算六个视场点,取值为 Kw = -1,-0.85,-0.707,-0.5,-0.3和0。上世纪80 年代以前计算机软、硬件条件还比较差,设计条件十分有限,编制软件时也必须考忠到计算机内存容量、计算时间等限制,一般除Kw =0的轴上点外 ...
、相对孔径和视场都较大时,初始解与最后的结果之间,差别就会更大。这表明,从一个初始解到成为一个可实用的解,尚需进行大量的像差校正和平衡工作。由于光学系统的种类很多,要求不一,其结构型式又千差万别而具各自的像差特征,因此我们必须了解校正光学系统像差的原则和常用方法。一、各光组以至各面的像差分布要合理。在考虑初始结构时,可将要校正的像差列成用P、W表示的方程组,这种方程组可能有多组精确解,也可能是病态的,或无解。若是前者,应选一合理的;若是后者,应取最小二乘解。总之,有多种解方程组的算法可以利用,在计算机上实现并不困难。然后,应尽量做到各个面上以较小的像差值相抵消,这样就不致于会有很大的高级像差。 ...
,获得一维线视场的空间信息,并利用机械运动完成沿轨方向扫描实现二维空间信息的获取,同时线视场的光谱信息在面阵探测器的第二维获得。图1推扫式高光谱成像原理线阵推扫的成像方式,在具有高速成像的同时,同一时间获得目标区域的所有光谱信息数据,保证每一个空间像素的光谱纯度,为客户提供真实准确的高光谱数据。通过选择感兴趣波段,芬兰SPECIM的FX系列高光谱相机还具有前所未有的高速数据采集度。且涵盖机载、实验室和地面端等方面,光谱范围覆盖紫外、可见光近红外、短波红外、中波红外和热红外(UV、VNIR、SWIR、MWIR、LWIR)等波段。图2FX系列高光谱,FX10(400-1000nm)/FX17(90 ...
对某一给定的视场计算其波像差的,故式中的视场因子是一常数,可并入系数内。实际计算波像差时,应根据系统孔径和视场的大小,确定波像差展开式中应取的项,然后计算多于或等于所取的项数,并以适当形式分布在半个光瞳上的光线的光程,分别求得其相对于主光线的光程差。这样,就可求得各项的系数,得到波像差随光瞳坐标而变的表示式。利用它就可对已知光瞳坐标的任何光线算出其波像差。相关文献:《几何光学 像差 光学设计》(第三版)——李晓彤 岑兆丰更多详情请联系昊量光电/欢迎直接联系昊量光电关于昊量光电:上海昊量光电设备有限公司是光电产品专业代理商,产品包括各类激光器、光电调制器、光学测量设备、光学元件等,涉及应用涵盖了 ...
说,获得一个视场可能需要几个小时的信号整合时间。因此,相干拉曼散射方法,如刺激拉曼散射效应,现在被广泛用于拉曼成像。在这个应用说明中,我们将描述Moku:Lab的锁相放大器是如何在波士顿大学的先进的刺激拉曼成像装置中实现的。介绍拉曼光谱是一种非破坏性的分析化学技术。它直接探测样品的振动模式。与电子光谱法相比,拉曼光谱法提供了高化学特异性,而不需要荧光标签。样品可以以完全无接触和无标签的方式被询问,防止对系统的破话。红外(IR)光谱是另一种常用的获得振动光谱的方法。红外光谱和拉曼光谱的选择规则是不同的;红外光谱对偶极子的变化很敏感,而拉曼光谱对偏振性的变化很敏感。这使得红外和拉曼成为一组特定化学 ...
束均匀分布在视场的垂直维度上(图2,底部面板,“加速”;参见“材料和方法”部分)。因此,在一个系统的n光束,每个光束必须只盖一条领土的全部水平方面的高度等于1 / n总高度存在误伤的观点,从而减少所需的总时间扫描等于n倍。尽管可以使用PMT或相机在水平能源部模式,垂直能源部模式需要一个相机或其他探测器有能力解决一些光源的数量大于等于光束能量来使用。更多详情请联系昊量光电/欢迎直接联系昊量光电关于昊量光电:上海昊量光电设备有限公司是光电产品专业代理商,产品包括各类激光器、光电调制器、光学测量设备、光学元件等,涉及应用涵盖了材料加工、光通讯、生物医疗、科学研究、国防、量子光学、生物显微、物联传感、 ...
而另一个视为视场光阑,与此对应有两种处理方法,一种是物在无穷远,孔阑在前焦面,为像方远心光路;另一种是物在前焦面,孔阑是后焦面,为物方远心光路。两种处理方法的几何光路与最终效果完全相同。无论用何种方法都必须同时控制物面像差和光阑像差,即对两对共轭面校正像差。若以输入面为孔径光阑来考虑,假设m级衍射光与光轴的夹角为,则按照衍射理论上式中,d为光栅常数,m为衍射级次。为使各谱线的像高成线性分布,像高应该有:式1由像差理论知,平行于光轴入(出)射的光线,正弦条件为或,即平行于光轴出射的主光线满足正弦条件,恰好就是保证(16-28)式成立的必要条件。傅里叶变换透镜要求全视场内的像质达到衍射极限,即波像 ...
或 投递简历至: hr@auniontech.com